OSI OVERHEAD CONVEYORIZED POWDER COATING SYSTEM
ITEM
NUMBER OSIPS24306
CLICK FOR PICTURES
REQUEST QUOTATION & DRAWINGS
SOLD
SPECIFICATIONS
"VERY GOOD TO EXCELLENT CONDITION"
QUALITY MANUFACTURED BY O.S.I. AND GEMA
WAS INSTALLED IN 1995
ONLY USED 2 YEARS – WELL MAINTAINED
5 STAGE STAINLESS STEEL WASHER
D.I. SYSTEM
GEMA AUTOMATIC BOOTH WITH NICE ACCESSORIES
EV ROOM
AIR DRIER
24" X 30 " OPENINGS
LONG CURE TIME AS WAS DESIGNED FOR HEAVY COMPRESSORS
COOL TUNNEL
HEAT RECOVERY SYSTEM
LINE SPEED BASED ON CLEANING DWELL TIMES NEEDED
THEY WERE RUNNING AT 6 FPM WITH 1 MINUTE WASH AND PHOS TIME
SPECIFICATIONS
SYSTEM OPENINGS: 24” X 30”
DESIGN LINE SPEED: DEPENDENT ON WASHER DWELL TIMES REQUIRED (WAS RAN AT 6 FPM)
Stainless Steel Washer:
- 5 Stage Stainless Steel
- Opening 24”w x 33”h
- 6 FPM design speed
- Plate & Frame Heating on Stages 1 & 3
- D.I. System with holding tank
- Access Platforms, access doors and dock lights each stage
- Drain stages 1/3 – 2/3 flow back design
- Square “D” disconnects each pump motor
- Control panel, 480/3/60
APPROXIMATE DIMENSIONS:
Entrance vestibule 4 ’
1st stage is heated 6 ’ Heated wash
Drain 3 ’
2nd stage 3 ’ Rinse
Drain 3 ’
3rd stage 6 ’ Heated Phosphate
Drain 3 ’
4th stage 3 ’ Rinse
Drain 3 ’
5th stage 3 ’ Final D.I. Rinse
Drain & Exit Vestibule 4 ’
APPROXIMATE TOTAL LENGTH 41’
Entrance and Exit Vestibules with containment exhausters.
Dry Off Oven:
- Straight Line Configuration
- opening 24”w x 30”h
- 27” high conveyor slot from top of conveyor to top of opening
- Air seals
- Floor mounted on heavy duty framed legs
- Distribution Ducts throughout
- Complete control panel, 480/3/60
- Exhaust System
- All existing exhaust stacking (12” diameter)
- Internal conveyor support structure throughout oven
- Overall Dimensions: 5’2” wide x 22’0” long x 12’3” high to top of blower
- Maximum temperature 250 F – Normal Operating 250 F
- Rated for 10,200 pounds per hour
4” I-Beam Conveyor System:
- Approx 650’0” total length
- Cat drive
- Air powered auto takeup
- 24” trolley centers
- 180 degree horz turns
- 90 degree horz turns
- 30 degree horz turns
- vert elevation change curves
- Digilube auto oiler
- External Floor supports
Gema Powder Booth/System:
- Complete Gema System with Automatic and Manual touch up
- Opening 24” x 30”
- Approx overall dimensions including man platform and collection module 18’4” long x 13’ wide x 98” high
- One Reclaim / color module
- Gema powder spray equipment
- 6 automatic guns with PGC controllers
- Gun Mounting stands, universal gun mounts, cables, housing and fittings
- 1 manual touch up station with Complete Manual Gun Set Up
- Powder hopper with powder pumps, rotary sieve and auto level control
- Drum unloader with transfer controls
- Flame detection system
- Main System Control Panel
- Remote Collector Control panel
- Pneumatic Control panel
- Vac Unit
- Air Drier (located outside wall of EV room)
- Emergency stop station
EV Room:
- Approx overall dimensions 28’5” long x 18’4” wide x 14’1” high
- Brite White insulated panel design
- Building ceiling mounted HVAC system
- Distribution ductwork (round design)
- Excellent lighting with Lighting Control panel
- Roll up door 8’ x 8’
- Man access door with window
- Conveyor pass through opening
Cure Oven/Cool Down Tunnel (Elevated):
- Elevated multipass Configuration
- opening 24”w x 30”h
- 27” high conveyor slot from top of conveyor to top of opening
- Bottom entry
- Floor mounted on heavy duty framing
- Distribution Ducts throughout
- Complete control panel, 480/3/60
- Exhaust System
- All existing exhaust stacking
- Internal conveyor support structure throughout
- Burner Box (Back mounted)
- Cooler fan and blower system (side mounted)
- Overall Dimensions: 22’ wide x 42’2” long x 18’6” (includes side mounted cooler and back mounted burner box)
- Maximum temperature 500 F – Normal Operating 400 F
- Rated for 10,200 pounds per hour
- FM rated design
- Provides extended cure time for heavier part mass if needed
- Heat recovery system which allows diverting heat back to plant or direct exhaust to outside
System Control Panel:
- Three door design with all required controls
- Nema 12
- NEC compliant
- Honeywell digital controllers
- A/B Panel View Touch Screen
- All required safety disconnects
- Removal and Re-Installation
By Customer
Or can be provided at additional cost
- Engineering, Start Up and Training
Included is:
Engineering for installation and layout to fit desired space
Included is:
System Drawings
System Manuals
TERMS & DELIVERY:
Terms: Net Due Prior to Shipment
F.O.B.: Shipping Point - MI
Delivery: Available for delivery immediately
Removal/Re-Installation by Customer or can be quoted at additional cost.
THIS
QUOTATION IS SUBJECT TO PRIOR SALE .
GENERAL:
- Technician(s)
familiar with the system could be available to assist with installation,
start-up, training and initial production. (At additional negotiated
cost)
- System installation
can be provided at additional cost.
- System F.O.B.
from its location.
- Detailed quotation
and specifications provided upon request
- Site visit to
view system can be arranged upon request.
PRICING:
RETURN
TO USED EQUIPMENT LISTINGS
Steven
G. Maurer
Industrial Finishing Tech., Inc.
800-755-9872
|
